Compaq Portable III

Resources

Wiki
oldcomputers.net – setup disks

Documents:
Product Bulletin
Motherboard jumpers
Service Manual

Internals

Motherboard

The computer will not access HDD when the CMOS battery is discharged or absent. There are two versions of the batteries possible:

  • Integrated inside Dallas DS1287 real time clock controller chip. It is easy to replace the integrated battery with an external one, following these instructions. Please mind that my computer is missing the back cover, so maybe the battery needs to be positioned differently, but the idea is basically the same.
  • Separately soldered to the board, with MC146818 chip instead of DS1287 – this version will have additional resistors, diodes and oscillator soldered near the chip and the battery. These components are missing in the Dallas version where some zero-ohm links are soldered instead.

Video Board

Floppy Disk Drive

Canon MD 5501

Hard Disk Drive

Conner CP3041

Power Supply

Display

Panasonic MD400F640PD5 – gas plasma display.

Keyboard

This is not the original keyboard coming with Portable III, but one taken from Compaq Portable 386. The keyboard seems to be compatible, also physically fits the cover perfectly.

Compaq Portable keyboards had cords in which the plastic cable coating broke easily with time and fell off leaving the bare cables visible. A vintage keyboard extender may be used as a replacement.

Reassembly

Other

Signal at pin 2 of the LCD screen 4-pin power connector

SDS00003

20 thoughts on “Compaq Portable III

  1. Hi, you can tell me the pinout scheme voltage of the 4-pin red molex connector that powers the LCD screen. Then the voltage is in DC or AC? please.

    Like

      1. Thanks. The purpose is to replace the original power supply with a modified atx pc or a modular power supply.

        Like

    1. thanks for your help. That white connector then connects to the red molex connector of the main power supply. Are the 200 dc volts negative?

      Like

  2. Love the machine and this is some excellent documentation! I have a Portable III myself, and am in the middle of replacing the old frayed keyboard with a new cable. I made the mistake though of not documenting the pinout of the old cable, and every combination of wiring I can think to try from the new cable to the keyboard’s internal connector doesn’t seem to work when testing on the machine. Do you happen to know the pinout between the keyboard port on the machine to the keyboard’s internal connector? Thanks in advance!

    Like

      1. Thanks for the reply and sorry this one is late as well! I have not yet solved my keyboard wiring. If you ever get the chance to open up yours and see the wiring that would help greatly!

        Like

  3. Does anyone have the pinouts for the power supply connector to the motherboard? I have a dead computer, and trying to start by verifying if I have a bad power supply. Turning it on, the only thing I get is a click from the relay. Both with and without everything hooked up. Thanks

    Like

  4. Hey Pawel, thanks for this trove of info! I’m missing all the screws holding the mainboard onto the chassis, but they don’t appear to be standard M3, and the service manual just says P/N 107386-001 but not what they actually are. Any idea on what thread pitch and size they are? Cheers!

    Like

    1. Hi silvervest1

      Just looking at a Compaq Portable 3 that I had in the loft.
      Motherboard has been trashed by the leaking Lithium battery!
      The screws I have removed appear to be ANC No 6 thread. 0.138″ od 32 tpi
      Regards

      Mike

      Like

    2. Sorry…..I’ve given the case screw info!

      The Motherboard screws are smaller : ANC 4 – 40 0.112″ 40 tpi

      Regards

      Mick

      Like

      1. Hey Mick, that’s fantastic, thanks! I needed the case screws as well so that’s tops.
        Are you able to measure their lengths as well? I’m guessing just based on the mounts that 1/4″ will be fine but nice to know!

        Like

      2. Hi Silvervest1

        Motherboard screws are 1/4 inch thread length with a T-10 star socket head and have a captive shake-proof washer.

        The case screws are T-15 star socket head with a plain washer.
        The two short ones for middle of the back are 1/2 inch long thread.
        The four corner screws are 4 inch long shank with 3/4 inch of thread.

        Regards

        Mick

        Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s